Parts & Accessories
The Super Patch Kit is comprised of a small plastic case, a piece of sandpaper for roughing up the tube and 6 peel-and-stick patches so no gluing is required. The patches stick fast thanks to 3M technology and they're thin and flexy to stretch with the tube. There's no easier way to patch a tube.
Topeak's SmartGauge D2 boasts a digital readout that goes up to 250 psi and it's compatible with Presta and Schrader valves, as well as shocks and suspension forks. The head rotates 180 degrees to get in tough spots, and an air release button helps you dial in the perfect pressure.
Planet Bike's Dial Gauge makes it easy to ensure you always have the right pressure in your tires, which makes the riding easy and helps prevent flats. Built to last, this quality gauge works on all valves and has a large easy-to-read dial.
Want a super-easy way to fix a flat? If you have tubeless tires on your mountain bike, all you need is Genuine Innovations' Tubeless Tire Repair Kit. No interior repair is needed, so you don't have to remove the tire. Just plug the hole with the self-vulcanizing plugs, inflate and ride away. The kit includes an insertion tool and five rope plugs.
Replacement ABS Flip Thread Chuck for all Lezyne High-Volume Dirt Floor Drive floor pumps. The red HV model is designed to optimize the performance of Lezyne's High-Volume floor pumps by allowing more air to pass through the chuck.
Upgrade any pump to the TwinHead pump head.
Klic Co2 head/cartridge adaptor replacement
Pssstttt. Tired of hearing that when you disconnect your shock pump? Well, hear it no more thanks to Topeak's Pressure-Rite. It's a must have for suspension fanatics as its ingenious design prevents air loss when adjusting shock and fork pressure. It's also available in a Presta version, perfect for disc wheels.
The TL-Head Set pump head is a new solution from SKS for all tubeless tire inflation. It is compatible with SKS floor pumps and all others with a 5.0-5.7mm hose size. The TL-Head Set can be used both for conventional pumping and with CO2 cartridges for a simple seating of tubeless tires. It comes in a practical set containing 2 tire levers and 2 16g CO2 cartridges. - Includes TL-Head, two 216g threaded cartridges and two tire levers - Compatible with Presta, Schrader and Dunlop valves
Upgrades any pump to a SmartHead pump head. Includes hardware, 40-inch hose, and SmartHead pump head.
- Attaches to air compressor to inflate tires in seconds - Designed with a variable rate trigger and a large, easy to read gauge - Spin-on Presta head with pressure release option and USA-made hose are included with Prestaflator - Prestaflator PLUS includes Schrader head and blower tip - Attachments are 6061-T6 alloy
The new Prestaflator Digital is made possible by Prestacycle's new Rapid Response Digital Gauge. During inflation, the gauge is capable of showing immediate changes in pressure, enabling fast inflation – now with supreme accuracy. The gauge uses highly accurate, non-wearing circuitry for pressure readings, so it does not wear-out or loose accuracy like traditional Dial gauges. Highly accurate readings are across the whole range, making this tool excellent for Fat Tire, Cyclocross, MTB as well as Road Bikes. Easy Tool-less replacement of the two CR2032 batteries (included).
Renew all the seals in your Prestaflator spin head. These o-rings fit the seals, Plus there are five (5) Presta Valve replacement washers. Replace as needed for a good connection to your tire valve.
Upgrade or replace your hose! Prestacycle's red hose is made in USA from reinforced polyurethane and is 3X more flexible than their previous black hose. New Quick-Click2 + Spin-on head. 300 psi working pressure, 13 inches length. Uses standard 1/4" threads. Smooth alloy clamps for comfortable use of the spinner head and corrosion resistance. Non-marring and resistant to moisture, fungi, oil, fuel, and grease as well as abrasion, impact, and tearing. Operating temperature range is from -90° to +175°F. Fits all previous Prestaflator tools, o-ring included.
Topeak Pump replacement parts and accessories. Includes all parts needed to rebuild TwinHead pumps.
Topeak's Presta Valve Extender is the perfect solution for getting to those hard-to-reach valve stems. It's precision-machined from aluminum and is designed to fit deep-dish carbon and aluminum rims. And, it comes with an O-ring seal to ensure a leak-free fit.
Park's Vulcanizing Patch Kit includes 4 round patches for small holes and 2 oval patches for wider cuts; a tube of self-vulcanizing glue that bonds the patches to your tube super securely; and sandpaper for preparing the punctured area for gluing. The kit comes in a small plastic box to fit in your seat bag or pack.
Why have your CO2 cartridges rattling around in a seat bag when you can get Xlab's X-Nut Inflation Holder and store them behind your saddle? It holds two threaded CO2 cartridges and an inflator (each sold separately) in an easy-access location. The X-Nut is compatible with Xlab's Carbon and Super Wings.
Problem Solvers 90 degree Presta valve inflator is used to inflate disc wheels, thanks to its narrow, low-profile head. • Presta valve • 90 degree inflator works with most pump heads
$4.95 - $5.95
Prestacycle's newest version of the Presta Head Gasket uses Urethane Elastomer. It’s softer and stronger. It lasts more than 5 times longer, gives a better seal and flexes to work anywhere along the Presta shaft for better tubeless tire application.
Lezyne's Slip Chuck is the perfect solution for getting to those hard-to-reach valve stems, especially on disc wheels. It's precision-machined from aluminum and is designed to fit Presta valves on deep-dish carbon disc wheels.
- Allows you to upgrade floor pumps to accept Prestacycle attachments - Spin-On presta head with pressure release option, USA-made 36" hose and hose clamp are included
A Schrader valve adapter allows using the JoeBlow Ace floor pump for quickly pumping forks and rear shocks. Built-in air release knob allows fine tuning air pressure.
Floor pump nylon braided hose with ABS flip thread chuck and connectors, compatible with all standard pressure floor pumps.
Prestacycle's new Mini Angle Presta Head has more room to fit into more wheels. It includes their newest version of the Mini Presta Head Gasket using Urethane Elastomer. It’s softer and stronger. It lasts more than 5 times longer, gives a better seal and flexes to work anywhere along the Presta shaft for better tubeless tire application.
Prestacycle redesigned the Presta Grommet in May 2012 to fit to modern standards. PRestacycle's design works so well, it’s been copied by others including major floor pump makers. Prestacycle's design engages the Presta valve just below the cap threads and requires less insertion. The head is now very easy to get on and off, and gives a nice “click” feeling when it’s installed in the right position. Safe for all types of Presta valves, including tubeless and tubeless-conversion valves. Will not harm newer lightweight performance valves. Fits all Prestaflator BIG Push/pull Presta heads. Also fits all Silca pump heads that use the 24.1 or 242 Gasket.
2 in 1 design! This unique product works like a mini air compressor that allows any floor pump to compress air into the 1000cc aluminum air tank. Then, it quickly releases a high volume of air to mount tubeless tire beads. The aluminum TubiBooster head also works as a CO2 inflator, compatible with Topeak threaded 16g/25g CO2 cartridges. - Pump Head Compatibility: Presta pumps - Tire Valve Compatibility: Presta / Schrader valves, Push to inflate - Air Tank: One liter, Store up to 200psi / 14bar air pressure (varies with the pump capacity) - Working Pressure - 1800psi / 124bar - Compatible with Topeak threaded 16g / 25g CO2 cartridges - Material: Aluminum
Made of heavy-duty hook-and-loop material, the Pump and U-Lock Tie also has a neoprene pad stitched next to the rectangular plastic common loop. Put the neoprene pad between your pump and frame, double-back the hook strip onto the loop, and you can rest assured that no matter how hard you ride, your pump will stay put. In addition to attaching pumps, the Pump Tie is also excellent for securing U-locks, fishing poles, and other delicate items that require a secure bond and a load-damping pad. - Dimensions: 1.5 x 10 inches - Weight: .5 ounces/14 grams
This mini sized gauge can be attached between the pump and valve to read pressures while pumping or used alone. Provides pressure readings up to 160 psi / 11 bar. Rotating gauge is easy to read and the head works with Presta, Schrader or Dunlop valves on bikes / motorcycles / car tires, forks or shocks while the Thumb Lock lever ensures an airtight seal. An air release button allows fine tuning of pressure. - Pump Head Compatibility: Presta / Schrader pumps - Tire Valve Compatibility: Presta / Schrader / Dunlop valves - Gauge: Reads 160psi / 11 bar, 1-1/2" analog - Pressure Tuning: Air release button - Material: Engineering grade polymer / aluminum - 360 degree rotatable gauge, Dust cap - Size: 6.2 x 5.8 x 3cm / 2.4" x 2.3" x 1.2" - Weight: 50g / 1.76oz
XLAB's versatile Multi-Strike Repair Holder provides fast access to your repair kit, whether you have tubular or clincher tires. Carry CO2s and an inflator on one side and a spare tube/tire or pump on the other! • VERSATILE MOUNTING - Will mount on DELTA single bottle systems or at the rear of the XLAB CARBON WING and SUPER WING (each sold separately) • STORAGE SAVER - Mounts to your hydration carrier (sold separately), saving space in your storage bag for your cell phone, nutrition and other important items • FAST ACCESS - Simply unscrew, and attach your inflator and CO2 cartridges. Simply unstrap your spare tire, tube or inflating foam sealant. • The CO2 Holder holds 2 CO2 Cartridges (included), and a NANOFLATOR or SPEED CHUCK inflator (each sold separately) • The Multi Holder can hold a tube, inflating foam sealant, TIRE MATE or tubular tire (each sold separately - must purchase optional XCW STRAP if storing a tubular tire) • Glass Reinforced Nylon • Chassis weight: 30 grams Includes: • Center Plate • Multi Holder • CO2 Holder • 2 AIR STRIKE CO2 Cartridges • Hardware Popular Clincher Setups (accessory items sold separately) • Tube & tire levers on Multi Holder. Two CO2 and a NANOFLATOR inflator on CO2 Holder. • 4 CO2 cartridges and NANOFLATOR inflator. (Purchase an extra CO2 Holder) Popular Tubular Setups (accessory items sold separately) • Tubular tire on Multi Holder. Two CO2 & NANOFLATOR inflator on CO2 Holder. • Tubular tire and inflating foam sealant. (Purchase an extra Multi Holder)
Page 1 of 3 Next page